Protect your precious electronics with this inline fuse holder. The cap seals out moisture to protect the circuit from the harsh environment. Simply splice this into your wiring. Fuses/circuit breakers sold separately. Fuse holders can be purchased individually.
Inline Fuse Holders
| Wire Size | Mounting Bracket | LED Indicator | ||
| (AWG) | Without Cap | With Cap | With Cap | With Cap |
| ATC/ATO | ||||
| 16 | (A)FH-ATO | (B)FH-ATO-W | (C)FH-ATO-16WP | (D)ATC-FHID |
| 12 | (A)FH-ATO-12 | (B)FH-ATO-12W | (C)FH-ATO-12WP | (D)FH-ATO-12-LED |
| Mini/ATM | ||||
| 18 | ------- | (E)FH-ATOM-18W | ------- | |
| 16 | ------- | (E)FH-ATOM-16W | (F)FH-ATOM-16WP | (D)ATM-FHID |
| 12 | ------- | (E)FH-ATOM-12W | (F)FH-ATOM-12WP | ------- |
| Mini/ATM Low-Profile | ||||
| 18 | ------- | (G)FH-LPM-18W | ------- | ------- |
| Maxi, 299, AF3, APX, Max | ||||
| 6 | ------- | (H)MAXI-H | ------- | (D)MAX-FHID |
| Micro3, ATL | ||||
| 14 | (I)FH-MICRO3-14W* | |||
| * Also has a 12 gauge ground | ||||
A |
B |
C |
D |
E |
F |
G |
H |
I |
Maxi Fuse Holder
Two screw posts allow you to connector your wire with a fork/ring terminal. Max 60 amps. Mounting hole in holder. Fuses sold separately.
Part #
MAXI-BLOCK
AMG Fuse Holder
Has two posts to connect your wiring to. Supports 8-2 gauge wire. 300 Amps. Fuses sold separately.
Part #
HMEG
Water Resistant AMG Fuse Holder
Fuse holder base and cover are securely sealed to create water resistant protection. 500 amps. AMG fuses sold separately
Part #
CH-880014
ANN/ANL Fuse Holder
Commonly found on fork lifts, fuse block supports ANN and ANL fuses. 800 Amps. Fuses sold separately.
Part #
SFR
Panel-Mount Fuse Holder
Use these panel-mount fuse holders with 1/4" x 1 1/4" glass fuses. Max panel thickness of 0.312" and 0.505" hole diameter.
| Amps | Volts | Connection | Fuse Size | |
| (A)15 | 250 | 3/16" Quick Connects | 1/4" X 1-1/4" | HTB-26I |
| (B)15 | 250 | 1/4" Quick Connects | 1/4" X 1-1/4" | HKP-HH |
| (C)30 | 250 | Solder | 1/4" X 1-1/4" | HKP |
| Replacement cap for HKP-HH and HKP #FHP-CAP | ||||
Add-A-Fuse Fuse Tap
This fuse holder allows you to replace one fuse with two fuses which allows you to protect an additional circuit. The bottom slot protects the existing circuit wired into the panel. The second fuse protects the line that comes off this unit that can be butt spliced (included) to another wire. The maximum combined current for both circuits is 30 amps. The maximum for the primary circuit is 25 amps and the maximum for the auxiliry circuit is 15 amps. Fuse/circuit breakers sold separately.
| Fuse Type | Pkg.Qty. | |
| ATC/ATO | FH-ATO-10A | 1 |
| Mini/ATM | FH-ATOM-10A | 1 |
| Mini/ATM Low-Profile | FH-ATMLP-10A | 1 |
| Micro/ATR | FH-MICRO-10A | 1 |
| Micro3/ATL | FH-MICRO3-10A | 1 |
ATC/ATO
Mini/ATM Low-Profile
Micro3/ATL
Easy-Install Inline Fuse Tap
Rather than splicing, simply hand squeeze this tap onto your wire and add an ATC / ATO fuse to protect your electronics. Fuses/circuit breakers sold separately.
Part #
ATO-TAP
Add a Circuit Fuse Taps
These fuse taps fit over the fuse to create a non-fused circuit.
| Fuse Type | Pkg. Qty. | |
| (A)ATC/ATO | ATC-TAP | Wire Leads |
| (B)Mini/ATM | ATM-TAP | Wire Leads |
Glass Inline Fuse Holders
Protect your precious electronics with this inline fuse holder. The cap seals out moisture to protect the circuit from the harsh environment. Simply splice this into your wiring. Fuses/circuit breakers sold separately. Fuse holders can be purchased individually.
| Wire Size | |||
| (AWG) | Maximum Amps | Connection | |
| AGC, 312, 313, GDL, GGC, MDL | |||
| 16 | 20 | Wire Leads | (A)GFH |
| 12 | 30 | Wire Leads | (B)GFH-12 |
| 18-12 | 30 | Crimp On | (C)GAFH-2 |
| Harsh-Environment | |||
| 18-12 | 30 | Crimp On | (D)HFB |
| 16-12 | 20 | Crimp On | (E)HFA |
| High-Voltage / 600 VAC | |||
| 12-8 | 30 | Wire Leads | (F)HEB-AA |
| Glass Fuse Accessories | |||
| Glass Fuse Clip (Not shown) | GFC-1/4 | ||
A |
B |
C |
D |
E |
F |
